{"title":"Dodge Sprinter","description":null,"products":[{"product_id":"1st-generation-dodge-sprinter-rear-bumper-kit","title":"1st Generation Dodge Sprinter Rear Bumper Kit","description":"\u003cp\u003eThis is a high clearance  DIY weld-together rear bumper kit for the 1st gen (1995-2006) Dodge Sprinter. It provides substantially improved rear end ground clearance over the flimsy factory rear bumper as well as excellent protection, heavy duty offroad recovery points and an integrated 2\" hitch receiver. The integrated hitch receiver is recessed into the bumper, providing a clean appearance and a smooth bumper surface that will easily slide over obstacles rather than hang up on them like a traditional hitch receiver can. The bumper mounts to the vehicle unibody using a total of 16 factory mounting points with included heavy duty mounting plates. While this is certainly overkill, it ensures that impact and pulling forces are evenly distributed over the vehicle chassis.\u003c\/p\u003e\u003cp\u003eDue to the Sprinter van's unibody construction, the design of the mounting system is especially critical. If a thick steel bumper is poorly mounted to the vehicle unibody, no matter how strong the bumper is, it will simply punch through the unibody mounting points should an impact occur. Our mounting system spreads forces evenly through the Sprinter's thin unibody frame structure, which substantially stiffens the bumper and protects the mounting interfaces. This makes for an extremely durable bumper that will easily shrug off trail impacts and scrapes as well as provide a stiff and secure structure to mount our optional swing out carrier arms to. \u003c\/p\u003e\u003cp\u003eAfter many design iterations, we settled on a bumper that sticks out from the van a few inches in the rear for protection but has very close-fitting corners. This maintains the full range of the Sprinter's double hinged doors as well as reducing weight and keeping the bumper as slim as possible. By doing this, we feel that we have achieved a very tidy bumper profile that will complement the lines of your Sprinter. The low profile design has also resulted in very reasonable weights of 74lbs for the steel bumper and 37lbs for the aluminum version. \u003c\/p\u003e\u003cp\u003eThe swing out carriers come in either a single or dual sided configuration and are built to accept a tire up to 37\" in diameter. Both carriers include mounting brackets for a hilift jack and other recovery items. The dual swing out includes the hilift mount as well as a lockable jerry can holder designed to fit two 20L NATO style jerry cans. These carriers feature heavy duty chromoly heim joint hinges, locking 2000lb toggle latches, T-handle spring pins, and a replaceable UHMW catch pad that provides secure, rattle free operation. The heim joints in conjunction with the toggle latch provide tons of adjustability, allowing for easy assembly and guaranteed alignment of the carrier latch. The single swing out add-on weighs 34lbs and the dual swing out add-on with gas can holder weighs 77lbs. \u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\u003cp\u003eDIY Weld-together kit - This bumper arrives as precision CNC-laser cut pieces that you then weld together (detailed assembly instructions included) \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eMaintains full usage of the factory spare tire mount underneath the vehicle \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003e All kits ship as clean, bare metal that is ready to weld out of the box - the Nitrogen laser cutting technology means no cutting edge oxidation or slag and thus easier and stronger welds \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eHeavy duty 3\/16\" plate steel construction for maximum offroad strength and durability \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eOptional 1\/4\" 5052 aluminum construction for a lightweight yet very durable overlanding setup (37lb weight savings) \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eSlim bumper profile is engineered to provide maximum ground clearance and complement the factory body lines \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eMounts using 16 factory mounting points - this distributes forces evenly into the Sprinter's relatively thin unibody structure \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eOptional LED lights include adjustable mounting tabs to mount the lights either on the swing outs or on top of the bumper \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eRecessed 2\" hitch receiver for a clean look and further clearance gains (While the hitch is very well reinforced, we cannot rate it for on-road towing due to the DIY welding nature of this kit) \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eReinforced 9\/16\" thick clevis mounts allow the use of 3\/4\" D-Rings and pull directly off of the frame for confident recoveries of heavily loaded vehicles \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eOptional Single and Dual Swing out carriers with spare tire mount, hilift jack mount and locking dual NATO can holder (dual swing out only)\u003c\/p\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264237981980,"sku":"CO73026","price":975.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_8ac8977c-e488-448e-b818-c0f549759bf6.jpg?v=1783513446"},{"product_id":"1st-generation-sprinter-front-hitch-bumper-kit","title":"1st Generation Sprinter Front Hitch Bumper Kit","description":"\u003cp style='font-family: Roboto, \"Odoo Unicode Support Noto\", sans-serif;'\u003eThis is a high clearance DIY weld-together hitch bumper kit for the 1st generation T1N (1995-2006) Mercedes\/Dodge Sprinter. We took our original  winch bumper and swapped out the winch plate for a built-in hitch receiver. This gives the versatility of a hitch receiver combined with a much slimmer bumper that only protrudes 2.25\" from the grill of the T1N Sprinter.  It features the same unibody-specific mounting system and LED pod light mounts, and gives excellent ground clearance. This bumper allows you to forget about approach angle and substantially improves the offroad capability of your Sprinter. It offers excellent protection from trail obstacles, animal strikes and distracted drivers and has been kept to a weight of 73lbs through careful design work. The main section of this bumper is CNC-bent out of a single piece of  3\/16\" P\u0026amp;O Steel. This greatly reduces the amount of welding and grinding required by you and makes for a cleaner finished product. If you are paying to have the bumper assembled by a welding shop, this significantly lowers the cost.\u003c\/p\u003e\u003cp style='font-family: Roboto, \"Odoo Unicode Support Noto\", sans-serif;'\u003eDue to the unibody construction of the Mercedes Sprinter van, there is not a lot to mount a hitch bumper capable of pulling the entire weight of the van. This makes the mounting system of the bumper especially critical. If a thick steel bumper is poorly mounted to the vehicle unibody, no matter how strong the bumper is, it will simply punch through the unibody mounting points should an impact occur. So, our engineers came up with an intermediate crossmember that bolts to your Mercedes Sprinter's main structural rails approximately 18\" back from the nose of the vehicle. This bumper then mounts to this crossmember plus the front of the Mercedes Sprinter's unibody frame using a total of six 1\/2\" bolts. This distributes impact and hitch forces evenly across your unibody frame. As far as we know, this is by far the most serious bumper mounting system available for the first generation Mercedes Sprinter van and will ensure that you can rely on this bumper when you need it most.\u003c\/p\u003e\u003cp style='font-family: Roboto, \"Odoo Unicode Support Noto\", sans-serif;'\u003eDespite the extra mounting points, this bumper still uses two factory frame mounting points to attach it to the vehicle, meaning that there is absolutely no guess-work required when fitting the bumper to the vehicle. The factory mounting points will locate the bumper perfectly on the vehicle, and then the supplied bumper plates comes pre-cut with the holes to locate the rest of the mounting holes needed. The six 1\/2\" bolts tie the hitch receiver of the bumper directly into the van and our suppled heavy duty crossmember, making for an extremely strong and stiff bumper that will not flex or shift under hard hitch use and recovery point pulls\u003c\/p\u003e\u003cp style='font-family: Roboto, \"Odoo Unicode Support Noto\", sans-serif;'\u003eWe finished this bumper off with four integrated light buckets for surface mount LED pod lights (custom light cut outs available by request, such as a 20\" light bar version), optional grill and headlight protection hoops for increased wildlife protection, and a hitch receiver to allow a variety of recovery and gear carrying options. The heavy duty 9\/16\" thick recovery points are placed directly in line with the T1N Sprinter frame to eliminate any leveraging effects. These recovery points are formed by laser cut steel plates that pass through the bumper shell and tie directly into the T1N Sprinter frame as part of the bumper's main mounting brackets. The recovery points then get welded to the in and outside of the bumper shell. These factors all combine to form recovery points that minimize stress on your T1N Sprinter frame and provide reliable recoveries of heavily loaded vehicles in the worst of offroad situations. What could make this bumper even better? The low profile design has resulted in very reasonable weights of 73lbs for the steel bumper and 36lbs for the aluminum version. Considering that this bumper replaces your factory bumper and associated components, the resulting weight increase to your T1N Sprinter is surprisingly minimal. This reduces added stress on your vehicle, maintains precious payload capacity, and allows you to keep your factory suspension if desired.\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\u003cp\u003eDIY Weld-together kit - This bumper arrives as precision CNC-laser cut and bent pieces that you then weld together (detailed assembly instructions included)\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eCNC-bent plates greatly reduces amount of welding and grinding required by you and makes for a cleaner finished product\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eLow profile design only protrudes 2.25\" front the center of the Sprinter grill - provides maximum ground clearance and complements the factory body lines\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eIncludes intermediate mounting crossmember which provides maximum strength for the most demanding offroad conditions\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eHeavy duty 3\/16\" plate steel construction for maximum offroad strength and durability\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eOptional 1\/4\" 5052 aluminum for a lightweight yet very durable overlanding setup (37lb weight savings)\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003e\u003cspan style=\"font-size: 13px;\"\u003eIntegrated 2\" Hitch Receiver provides options for mounting an external winch tray or other hitch accessories\u003c\/span\u003e\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eReinforced 9\/16\" thick clevis mounts allow the use of 3\/4\" D-Rings and pull directly off of the frame for confident recoveries of heavily loaded vehicles\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eFour integrated LED pod mounts – slotted mounting tabs give adjustment to fit a variety of lights\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eIntegrated license plate mount\u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eOptional heavy duty grill and headlight tubing for added protection\u003c\/p\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264238145820,"sku":"CO13071","price":925.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_76b29107-9c7a-4d49-93c7-813dc51f74d0.jpg?v=1783516720"},{"product_id":"2nd-generation-dodge-sprinter-high-clearance-front-bumper-kit","title":"2nd Generation Dodge Sprinter High Clearance Front Bumper Kit","description":"\u003cp\u003e***We have one brand new welded and powder coated bumper available for purchase. Vancouver, BC pickup only. Please \u003ca href=\"\/contact\"\u003econtact us\u003c\/a\u003e for details.*** This is a high clearance DIY weld-together winch bumper kit for the 2nd gen (2007-2013) Dodge\/Mercedes Sprinter. It features a reinforced bolt-on design, protected winch mount, LED pod light mounts and excellent ground clearance. This bumper allows you to forget about approach angle and substantially improves the offroad capability of your Sprinter. It offers excellent protection from trail obstacles, animal strikes and distracted drivers and has been kept to a weight of 105lbs through careful design work. The main section of this bumper is CNC-bent out of a single piece of  3\/16\" P\u0026amp;O Steel. This greatly reduces the amount of welding and grinding required by you and makes for a cleaner finished product. If you are paying to have the bumper assembled by a welding shop, this significantly lowers the cost.\u003c\/p\u003e\u003cp\u003eDue to the construction of the front end of the Dodge Sprinter van, there are only four tiny M8 factory bolt holes per side available to mount an aftermarket bumper. While this is totally inadequate for an offroad winch bumper, some aftermarket bumpers mount to the Dodge Sprinter using only these mounting points! If a thick steel bumper is poorly mounted to the vehicle, no matter how strong the bumper is, it will simply fail at its mounting points should an impact or recovery pull occur. Instead, our engineers came up with intermediate mounting brackets that bolt to your Dodge Sprinter's main structural frame rails approximately 8\" back from the end of the frame. Two 1\/2\" bolts per side get run through the van's frame rails and into these heavy duty brackets. This results in a total of 12 mounting points between this bumper and your Dodge sprinter van. While this is certainly overkill, it ensures that impact and winching forces are evenly distributed across your Dodge Sprinter's frame. As far as we know, this is by far the most serious winch bumper mounting system available for the 2nd generation Dodge Sprinter van and will ensure that you can rely on this bumper when you need it most. \u003c\/p\u003e\u003cp\u003eDespite the extra mounting points, this bumper still uses the factory M8 frame mounting points to attach it to the vehicle as well, meaning that there is absolutely no guess-work required when fitting the bumper to the vehicle. The factory mounting points will locate the bumper perfectly on the vehicle, and then the supplied bumper plates come pre-cut with the holes to locate the rest of the mounting holes needed. The four 1\/2\" bolts tie the winch area of the bumper directly into the vehicle's main frame rails, making for an extremely strong and stiff bumper that will not flex or shift under hard winching and recovery point pulls. Other notable features include the four integrated LED pod light mounts, optional grill and headlight protection hoops for increased wildlife protection, and optional front hitch receiver to allow a variety of recovery and gear carrying options. \u003c\/p\u003e\u003cp\u003eThe profile of this bumper has been designed with maximum ground clearance and approach angles put first. The bumper sits as high and tight to the front of the 2nd generation (2007-2013) Dodge Sprinter as possible, while the angled lower faces will smoothly slide over obstacles and ensure you do not get hung up on the trail. The side wings of this bumper wrap around to the front wheel wells and tie directly into the main frame mounting plates for true offroad protection. These side wings will take a serious hit without flexing or deflecting into the vehicle body. We know that most Sprinter owners want to run oversized tires and more aggressive wheel offsets. This can create interference issues with the stock front bumper. We have thought ahead and specifically designed these bumper side wings to easily clear 35\" tires. \u003c\/p\u003e\u003cp\u003eWe finished this bumper off with four integrated light buckets for surface mount LED pod lights (custom light cut outs available by request, such as a 20\" or 30\" light bar cut out), an integrated winch mount to accept all standard 8-12k lb winches with removable solenoids, and heavy duty 9\/16\" recovery points that are placed directly in line with the Sprinter frame to eliminate any leveraging effects. These recovery points are formed by laser cut steel plates that pass through the bumper shell and tie directly into the Sprinter frame as part of the bumper's main mounting brackets. The recovery points then get welded to the in and outside of the bumper shell. These factors all combine to form recovery points that minimize stress on your Sprinter frame and provide reliable recoveries of heavily loaded vehicles in the worst of offroad situations. The low profile design has resulted in very reasonable weights of 107lbs for the steel bumper and 55lbs for the aluminum version. Considering that this bumper replaces your factory bumper and associated components, the resulting weight increase to your Sprinter is surprisingly minimal. This reduces added stress on your vehicle, maintains precious payload capacity, and allows you to keep your factory suspension if desired. \u003c\/p\u003e\u003cp\u003eOther notable features include the optional grill and headlight protection hoops for increased wildlife protection and an optional front hitch receiver to allow a variety of recovery and gear carrying options. (available by custom request - please send us an email and we'd be happy to discuss further). \u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\u003cp\u003eDIY Weld-together kit - This bumper arrives as precision CNC-laser cut pieces that you then weld together (detailed assembly instructions included) \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eCNC-bent plates greatly reduces amount of welding and grinding required by you and makes for a cleaner finished product \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eLow profile design is engineered to provide maximum ground clearance and complement the factory body lines \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eIncludes intermediate mounting brackets which provide maximum strength for the most demanding offroad conditions - bumper mounts to frame using a total of 12 mounting points! \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eHeavy duty 3\/16\" plate steel construction for maximum offroad strength and durability \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eOptional 1\/4\" 5052 aluminum for a lightweight yet very durable overlanding setup (53lb weight savings) \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eProtected winch mount fits all standard 8000-12,000lb winches with removable solenoids \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eReinforced 9\/16\" thick clevis mounts allow the use of 3\/4\" D-Rings and pull directly off of the frame for confident recoveries of heavily loaded vehicles \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eFour integrated LED pod mounts – slotted mounting tabs give adjustment to fit a variety of lights \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eIntegrated license plate mount \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eOptional heavy duty grill and headlight tubing for added protection \u003c\/p\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264238276892,"sku":"CO25233","price":915.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_da0e2866-15b8-4ae8-a200-7496dd24c0a5.jpg?v=1783514091"},{"product_id":"2014-2018-dodge-sprinter-high-clearance-front-bumper-kit","title":"2014-2018 Dodge Sprinter High Clearance Front Bumper Kit","description":"\u003cp\u003eThis is a high clearance DIY weld-together winch bumper kit for the post-facelift 2nd gen (2014-2018) Mercedes\/Dodge Sprinter. It features a reinforced bolt-on design, protected winch mount, LED pod and 30\" light bar mounts and excellent ground clearance. This bumper allows you to forget about approach angle and substantially improves the offroad capability of your Mercedes\/Dodge Sprinter. It offers excellent protection from trail obstacles, animal strikes and distracted drivers and has been kept to a weight of 97lbs through careful design work. Trimming of the factory plastic bumper cover is required, however this is a cosmetic piece that is easily replaceable should you wish to return to the factory front bumper parts in the future. Absolutely no drilling, trimming or modification of the vehicle frame\/chassis is required.\u003c\/p\u003e\u003cp\u003eDue to the construction of the front end of the Mercedes Sprinter van, there are only four tiny M8 factory bolt holes per side available to mount an aftermarket bumper. While this is totally inadequate for an offroad winch bumper, some aftermarket bumpers mount to the Mercedes Sprinter using only these mounting points! If a thick steel bumper is poorly mounted to the vehicle, no matter how strong the bumper is, it will simply fail at its mounting points should an impact or recovery pull occur. Instead, our engineers came up with intermediate mounting brackets that bolt to your Mercedes Sprinter's main structural frame rails approximately 10\" back from the end of the frame. This is done using the six factory M12 mounting points already present on your Sprinter's frame, meaning that this bumper requires absolutely no frame\/chassis cutting, drilling or modification of any kind! The end result is a total of 14 mounting points between this bumper and your Mercedes sprinter van. While this is certainly overkill, it ensures that impact and winching forces are evenly distributed across your Mercedes Sprinter's frame. As far as we know, this is by far the most serious winch bumper mounting system available for the 2014-2018 generation Mercedes Sprinter van and will ensure that you can rely on this bumper when you need it most. \u003c\/p\u003e\u003cp\u003eThe profile of this bumper has been designed with maximum ground clearance and approach angles put first. The bumper sits as high and tight to the front of the 2nd generation (2014-2018) Mercedes\/Dodge Sprinter as possible, while the angled lower faces will smoothly slide over obstacles and ensure you do not get hung up on the trail. The side wings of this bumper wrap around to the front wheel wells and tie directly into the main frame mounting plates for true offroad protection. These side wings will take a serious hit without flexing or deflecting into the vehicle body. We know that most 4x4 Sprinter owners want to run oversized tires and more aggressive wheel offsets. This can create interference issues with the stock front bumper. We have thought ahead and specifically designed these bumper side wings to easily clear 35\" tires. \u003c\/p\u003e\u003cp\u003eThis bumper is also available with an optional lower skid plate that provides a smooth surface to slide across trail obstacles and protects your vulnerable engine bay parts. This is especially important on the Sprinter chassis, as the factory parts leave your engine oil pan and front differential totally exposed to mud and trail impacts. In fact, the Sprinter van that we had into the shop to design this bumper had this area packed full of dried mud that had to be chipped out! Our skid plate covers this area and is made from heavy duty 3\/16\" steel or 1\/4\" aluminum, ensuring that it can take the heavy trail hits and protect your expensive drivetrain and engine parts. This skid plate is fully CNC-bent into shape out of a single plate of metal and only requires two very small 1\" long welds to complete it. \u003c\/p\u003e\u003cp\u003eThe main section of this bumper is also CNC-bent out of a single piece of  3\/16\" P\u0026amp;O Steel or 1\/4\" aluminum. This greatly reduces the amount of welding and grinding required by you and makes for a cleaner finished product. If you are paying to have the bumper assembled by a welding shop, this significantly lowers the cost. \u003c\/p\u003e\u003cp\u003eWe finished this bumper off with two integrated light buckets for surface mount LED pod lights, a 30\" single row light bar mount (custom light cut outs available by request), an integrated winch mount to accept all standard 8-12k lb winches with removable solenoids, and heavy duty 9\/16\" recovery points that are placed directly in line with the Sprinter frame to eliminate any leveraging effects. These recovery points are formed by laser cut steel plates that pass through the bumper shell and tie directly into the Sprinter frame as part of the bumper's main mounting brackets. The recovery points then get welded to the in and outside of the bumper shell. These factors all combine to form recovery points that minimize stress on your Sprinter frame and provide reliable recoveries of heavily loaded vehicles in the worst of offroad situations. The low profile design has resulted in very reasonable weights of 97lbs for the steel bumper and 48lbs for the aluminum version. Considering that this bumper replaces your factory bumper and associated components, the resulting weight increase to your Sprinter is surprisingly minimal. This reduces added stress on your vehicle, maintains precious payload capacity, and allows you to keep your factory suspension if desired. \u003c\/p\u003e\u003cp\u003eOther notable features include the optional grill and headlight protection hoops for increased wildlife protection and an optional front hitch receiver to allow a variety of recovery and gear carrying options. (available by custom request - please send us an email and we'd be happy to discuss further). \u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\u003cp\u003eDIY Weld-together kit - This bumper arrives as precision CNC-laser cut pieces that you then weld together (detailed assembly instructions included) \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eCNC-bent plates greatly reduces amount of welding and grinding required by you and makes for a cleaner finished product \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eTrimming of the factory plastic bumper cover is required (detailed trimming instructions included), however absolutely no drilling trimming or modification of the vehicle frame\/chassis is required. \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eLow profile design is engineered to provide maximum ground clearance and complement the factory body lines \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eIncludes intermediate mounting brackets which provide maximum strength for the most demanding offroad conditions - bumper mounts to frame using a total of 14 factory mounting points \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eHeavy duty 3\/16\" plate steel construction for maximum offroad strength and durability \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eOptional 1\/4\" 5052 aluminum for a lightweight yet very durable overlanding setup (49lb weight savings) \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eProtected winch mount fits all standard 8000-12,000lb winches with removable solenoids \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eReinforced 9\/16\" thick clevis mounts allow the use of 3\/4\" D-Rings and pull directly off of the frame for confident recoveries of heavily loaded vehicles \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eTwo integrated LED pod mounts – slotted mounting tabs give adjustment to fit a variety of lights \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eIntegrated 30″ Light bar mount – fits all standard 30″ single row light bars and includes adjustable mounts \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eIntegrated license plate mount \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eOptional heavy duty grill and headlight tubing for added protection \u003c\/p\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264238539036,"sku":"CO92186","price":940.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_808e962e-ab81-449e-a2f6-b482889f308e.jpg?v=1783513450"}],"url":"https:\/\/shop-nz.dev-everfruitdigital.com\/collections\/dodge-sprinter.oembed","provider":"Coastal Offroad","version":"1.0","type":"link"}