{"title":"Toyota Land Cruiser 200","description":null,"products":[{"product_id":"kickout-rock-slider-weld-together-kit","title":"Kickout Rock Slider Weld-Together Kit","description":"\u003cp\u003e    This is a DIY weld-together rock slider kit that is available in 65\", 68\" and 71\" lengths. The 65\" length fits the 1st-3rd gen 4Runner, 1st gen single cab Tacoma, FJ Cruiser, 1st-2nd gen Nissan Xterra and R50 Nissan Pathfinder. The 68\" length fits the 4th-5th gen 4Runner, 80-series Land Cruiser, Lexus GX470 and GX460, and Nissan R51 Pathfinder. The 71\" length fits the 100-series Land Cruiser, Lexus LX470 and Nissan Frontier.\u003c\/p\u003e\u003cp\u003e\u003cb\u003eWhen placing your order, please enter your vehicle year and model into the notes section so we can verify fitment\u003c\/b\u003e\u003c\/p\u003e\u003cp\u003e    These aren't your average tube sliders. The square inner tubes, laser CNC-cut step plates and tapered ends really set these sliders apart. The inner rails and mounting legs are made from 2x2\" wall square tubing and finished with massive CNC-cut frame mounting plates and gussets that ensure these sliders will stand up to the harshest abuse you can throw at them. Some sliders use skimpy round tubing mounting legs that weld directly to the side of the thin factory frame rails. These can dent the frame rails over time and even punch right through them under hard hits. With this kit, the provided frame plates spread impact loads evenly over your frame rails and provide a huge amount of surface area to place your welds. The massive CNC cut gussets bridge the angle between the mounting legs and mounting plates (the highest stress areas in the entire slider) and create super stiff sliders that will not bend or flex excessively under the most extreme conditions! As a nice finishing touch, the ends of the square main rails are tapered at a 45 degree angle to ensure that they will not become battering rams if faced with a rock or stump. \u003c\/p\u003e\u003cp\u003eThese sliders come in pieces that are pre-bent and pre-cut. Simply line them up as per the provided assembly directions and diagrams, weld them together, and install them on your truck. Simply put, these sliders make for a perfect first-time welding project! To make it even easier, the kits ship with clear and detailed step by step directions that are accompanied by professional CAD diagrams. The 6 (3 per side) mounting legs ship over-length so the sliders can be positioned at your preferred angle and distance from the vehicle. Angle them up tight to the rocker panels for maximum ground clearance or set them level to provide a convenient step to access your roof rack. The pictured sliders are set at a 15 degree angle to provide a happy medium.\u003c\/p\u003e\u003cp\u003eThis is a weld-on rock slider kit that requires welding to your vehicle's frame. When ordering this product, please ensure that it complies with the local regulations in your jurisdiction. We do also have bolt-on rock slider kits for many vehicle makes and models and are continuing to expand our lineup of bolt-on rock sliders. Please search your vehicle model on our shop page for more details on if we have a bolt-on option for your vehicle.\" \u003c\/p\u003e\u003cp\u003e\u003cb\u003eWhen placing your order, please enter your vehicle year and model into the notes section so we can verify fitment \u003c\/b\u003e\u003c\/p\u003e\u003cul\u003e\n\u003cli\u003e\u003cp\u003eDIY Weld-together rock slider kit that arrives in CNC-laser cut and bent pieces that you then weld together - everything you need for assembly and installation included \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eDetailed instructions and diagrams - the step by step directions and diagrams make these a perfect first welding project \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eCNC-cut step plates look great, protect your rocker panels from rock debris spray and provide a convenient step to access to the cabin, roof rack and\/or pickup bed \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eMultiple length options ensure full wheel well to wheel well protection for your vehicle \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003e2x2 1\/8\" wall square tubing inner rails and mounting legs provide excellent foundational support compared to lesser round tube sliders \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eLarge frame mounting plates and gussets distribute forces evenly into your vehicle frame to prevent damage \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eHilift jack can be used anywhere along the slider length to lift the vehicle \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003e45 degree tapered inner rails to glance off obstacles \u003c\/p\u003e\u003c\/li\u003e\n\u003cli\u003e\u003cp\u003eSold in pairs\u003c\/p\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54264247812380,"sku":"CO0575","price":697.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_e0c30ec8-b1fd-464c-bb74-15e0d1997e0a.jpg?v=1783514589"},{"product_id":"2007-2021-tundra-sequoia-land-cruiser-cab-mount-chop-plate","title":"2007-2021 Tundra, Sequoia, Land Cruiser Cab Mount Chop Plate","description":"\u003cp class=\"p1\"\u003eThis is a set (left and right) of cab mount chop plates that fits the 2007-2021 Toyota Tundra, 2008-2021 Toyota Sequoia and 2008-2021 200 Series Toyota Land Cruiser.\u003c\/p\u003e\u003cp\u003eWhen adding larger tires onto any of these vehicles, the first rubbing issues will occur on the cab mount while turning. This is located at the rear of the front wheel wells. The solution to this problem is to trim the cab mount back and replace the trimmed section with a new plate that gives more tire clearance. Our cab mount chop plates are the only ones on the market that are notched to allow tighter fitment around the cab mount bolt. This allows you to tuck this plate further back and run 37\" tires at any lift height without rubbing on the body mount! We also have made a very thorough article that shows how to install these plates as well as covering every detail required to fit 37\" tires on your 2007+ Tundra, Sequoia or Land Cruiser. That article can be found \u003ca href=\"\/blog\/general-ordering-7\/clearing-37-tires-on-a-toyota-tundra-at-any-ride-height-19\"\u003ehere\u003c\/a\u003e: \u003c\/p\u003e\u003cp\u003e•    CNC Laser cut steel plates fill the gap after performing the cab mount chop modification\u003c\/p\u003e\u003cp\u003e•    Fits 2007-2021 Toyota Tundra, 2008-2021 Toyota Sequoia and 2008-2021 200 Series Toyota Land Cruiser\u003c\/p\u003e\u003cp\u003e•    Allows for fitment of 37″ Tires at ANY lift height without any rubbing on the cab mount. (**Must run a wheel with an offset greater than +15mm, some rubbing may occur with 37’s paired with a lower wheel offset)\u003c\/p\u003e\u003cp\u003e•    Sold as a pair (left and right)\u003c\/p\u003e\u003cp\u003e•    Grinding and welding of the vehicle cab mounts required for installation\u003c\/p\u003e\u003cp\u003eCheck out our comprehensive article that covers the installation of these plates as well as every detail required for fitting 37″ tires.\u003c\/p\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54289164435740,"sku":"CO95241","price":35.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_b5f016b9-f3ef-4e8a-8dc6-abf8755a803f.jpg?v=1783585690"},{"product_id":"2007-2021-tundra-sequoia-land-cruiser-front-bumper-shim-kit","title":"2007-2021 Tundra, Sequoia, Land Cruiser Front Bumper Shim Kit","description":"\u003cp class=\"p1\"\u003eThis is a set (left and right) of front bumper shim plates that fits the 2007-2021 Toyota Tundra, 2008-2021 Toyota Sequoia and 2008-2021 200 Series Toyota Land Cruiser.\u003c\/p\u003e\u003cp\u003eWhen adding larger tires onto any of these vehicles, you will likely encounter rubbing on the bottom corners of the factory front bumper. These spacers push your front bumper forwards by 1\/2\" to provide additional tire clearance and remove the need to trim the bumper or inner fender liners (**Very extreme wheel offset\/tire combinations may still require additional trimming). Made from 5052 aluminum, these CNC laser cut plates have clean, polished edges and will not rust. Each kit consists of four 1\/4\" thick spacers, allowing you to move your bumper forwards in 1\/4\" increments depending on your tire clearance needs.\u003c\/p\u003e\u003cp\u003eWe also have made a very thorough article that shows how to install these plates as well as covering every detail required to fit 37\" tires on your 2007+ Tundra, Sequoia or Land Cruiser. That article can be found \u003ca href=\"\/blog\/general-ordering-7\/clearing-37-tires-on-a-toyota-tundra-at-any-ride-height-19\"\u003ehere\u003c\/a\u003e: \u003c\/p\u003e\u003cp\u003e• CNC Laser cut 5052 aluminum plates push your front bumper forwards by 1\/2″ to give additional clearance for larger tires.\u003c\/p\u003e\u003cp\u003e• Removes the need to trim your factory bumper and fender liners in order to fit larger tires.\u003c\/p\u003e\u003cp\u003e• Fits 2007-2021 Toyota Tundra, 2008-2021 Toyota Sequoia and 2008-2021 200 Series Toyota Land Cruiser\u003c\/p\u003e\u003cp\u003e• Aluminum finish looks great and will not rust\u003c\/p\u003e\u003cp\u003e• Very easy installation: simply unbolt your front bumper, slide these spaces over your factory frame studs, and reinstall your bumper. Detailed step by step directions for bumper removal are included.\u003c\/p\u003e\u003cp\u003e• Sold as a complete left and right set\u003c\/p\u003e\u003cp\u003eCheck out our comprehensive article that covers the installation of these plates as well as every detail required for fitting 37″ tires.\u003c\/p\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54289167581468,"sku":"CO95249","price":89.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_01cff61c-2fe5-4212-94d5-fcd6ee64e73f.jpg?v=1783585707"},{"product_id":"2007-2021-tundra-sequoia-land-cruiser-front-suspension-bumpstop-spacer-kit","title":"2007-2021 Tundra, Sequoia, Land Cruiser Front Suspension Bumpstop Spacer Kit","description":"\u003cp class=\"p1\"\u003eThis is a set (left and right) of front suspension bumpstop spacer plates that fits the 2007-2021 Toyota Tundra, 2008-2021 Toyota Sequoia and 2008-2021 200 Series Toyota Land Cruiser. These small spacers are designed to allow you to run 37\" tires without needing to trim the vehicle's outer fenders or remove the inner fender liners.\u003c\/p\u003e\u003cp\u003eBumpstop spacers are spacers that you add between your suspension bumpstops and the vehicle frame. These spacers lower your bumpstops so that your suspension will bottom out sooner. Normally, we are against limiting suspension travel for the sake of reduced tire rub and we even wrote a whole article that is based around clearing big tires throughout the suspension’s entire travel range. HOWEVER, in the case of running 37” tires on the Tundra, we make an exception by adding some tiny bump stop spacers and here is why: With a 37” tire jacked up to full compression using the method given in our article, the tire will not hit the top of the fender but it will be within a couple millimeters of it. But when we are out in the wilderness and encounter a hard suspension bottom-out situation, such as bumping a ledge obstacle to get up it or hitting an unexpectedly big dip on an FSR a little too fast, the suspension will compress (just as we simulated in the shop) plus there will also be flex in the vehicle chassis, body mounts, suspension bushings, etc that will result in the tires compressing a little bit further than what we can replicate in the shop. For this reason, its important to ensure that we give the tires at least an extra ½” of space to account for the additional flex and movement that occurs within the vehicle during a hard bottom out situation. Our solution is to add a 3\/16” thick front bumpstop spacer and a ¼” thick rear bumpstop spacer. Due to the relationships between the suspension pivot points, bumpstop locations, and tire location, this will result in a wheel travel reduction of just about ½” which is perfect.\u003c\/p\u003e\u003cp\u003eSo yes, you will theoretically lose ½” of wheel travel, but this is wheel travel at the very end of the travel range that will only be reached during hard bottom-out situations. If you’d prefer to avoid the bumpstop spacers when running 37\" tires, the alternative is to cut and re-seal the vehicle’s outer fenders and remove the inner fender liners altogether. This adds a lot of work to the overall procedure, as well as visible cutting and modifications to the vehicle’s outer fenders that risks premature rusting if not sealed properly. If you are running a long travel kit, this effort is worth it. However, if you are running stock lower control arms with a typical lift or “mid travel” kit, you will not lose any real suspension performance by limiting that last ½” of fender-crunching wheel travel.\u003c\/p\u003e\u003cp\u003eCheck out our very thorough article that shows how to install these plates as well as covering every detail required to fit 37\" tires on your 2007+ Tundra, Sequoia or Land Cruiser. That article can be found \u003ca href=\"\/blog\/general-ordering-7\/clearing-37-tires-on-a-toyota-tundra-at-any-ride-height-19\"\u003ehere\u003c\/a\u003e: \u003c\/p\u003e\u003cp\u003e•    CNC Laser cut 5052 aluminum plates space your factory bumpstops down just enough to ensure that 37″ tires will not contact the vehicle fenders during hard offroad compressions\u003c\/p\u003e\u003cp\u003e•    Limits the last 1\/2″ of front wheel travel, removing the need to trim your outer fenders and remove your inner fender liners when fitting 37″ tires.\u003c\/p\u003e\u003cp\u003e•    Fits 2007-2021 Toyota Tundra, 2008-2021 Toyota Sequoia and 2008-2021 200 Series Toyota Land Cruiser\u003c\/p\u003e\u003cp\u003e•    Aluminum finish looks great and will not rust\u003c\/p\u003e\u003cp\u003e•    Very easy installation: simply unbolt your factory bumpstops, slide these spaces over your factory bumpstop studs, and reinstall your bumpstops.\u003c\/p\u003e\u003cp\u003e•    Sold as a complete left and right set. Each kit consists of two 1\/4″ thick spacers and two 3\/16″ thick spacers to correctly account for the difference between the front and rear bumpstop locations.\u003c\/p\u003e\u003cp\u003eCheck out our comprehensive \u003ca href=\"\/blog\/general-ordering-7\/clearing-37-tires-on-a-toyota-tundra-at-any-ride-height-19\"\u003earticle\u003c\/a\u003e that covers the installation of these plates as well as every detail required for fitting 37″ tires.\u003c\/p\u003e","brand":"Coastal Offroad","offers":[{"title":"Default Title","offer_id":54289167679772,"sku":"CO95251","price":31.0,"currency_code":"CAD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0957\/8659\/8684\/files\/image_1920_109967f9-4268-400a-804d-9f94920a14a3.jpg?v=1783585723"}],"url":"https:\/\/shop-nz.dev-everfruitdigital.com\/collections\/toyota-land-cruiser-200.oembed","provider":"Coastal Offroad","version":"1.0","type":"link"}